Update Procedure¶

This section contains an overview of the NetEye update procedure. Please read it carefully before actually starting the update procedure.

NetEye installations can be updated by using the command neteye update, which will carry out a number of tasks, some of which on Clusters only. The command requires almost no interaction and should normally conclude successfully, except for the following situations:

A (health) check fails
An .rpmnew and/or .rpmsave file is found
The NetEye Active Node is in standby mode

Check the sections NetEye Single Instance and NetEye Cluster for details on the tasks executed and section Troubleshooting for directions on how to tackle these problems.

NetEye Single Instance¶

On a NetEye Single Instance, the update procedure is carried out by running:

# nohup neteye update

All the tasks carried out by the command are listed in section neteye update.

If the command is successful, a message will inform you that the update procedure has concluded successful; otherwise, check section Troubleshooting to fix the problems, then run the command again.

Finally, to ensure that any potentially stopped and/or newly installed NetEye services are running, use the command

# neteye start

NetEye Cluster¶

Updating a cluster will take a nontrivial amount of time, however no downtime needs to be planned. During the cluster update, individual nodes will be put into standby mode and so overall cluster performance will be degraded until the update procedure is completed and all nodes are removed from standby mode.

An estimate for the time needed for a full upgrade (update + upgrade) when the cluster is healthy, there is no additional NetEye modules installed, and the procedure is successful is approximately 30 minutes, plus 15 minutes per node.

Warning

This estimate does not include the time required to download the packages and for any manual intervention due to failure of tasks during the execution of the neteye update and neteye upgrade commands.

Prerequisites¶

Kernel and DRBD version

It is critical that the versions of the Linux kernel and drbd match. Clusters must not be updated if a package update would cause a version mismatch.

You can find the currently installed and the available package versions by running the following two commands, then checking that the version numbers reported in the line Installed Packages match those reported on the last line of the Available Packages column.

# dnf list kernel --showduplicates

Installed Packages
kernel.x86_64      3.10.0-1160.42.2.el7      @updates

# dnf list kmod-drbd --showduplicates

Installed Packages
kmod-drbd.x86_64      9.0.30_3.10.0_1160.42.2-1      @neteye-os

In this case, the versions match: 3.10.0-1160.42.2.el7 9.0.30_3.10.0_1160.42.2-1

If dnf reports that either the kernel or drbd has a newer version available, you need to check that after an update their versions will again be the same.

Running the Update¶

On a NetEye Single Instance, the update procedure is carried out by running:

# nohup neteye update

All the tasks carried out by the command are listed in section neteye update.

If the command is successful, a message will inform you that the update procedure has concluded successful; otherwise, check section Troubleshooting to fix the problems, then run the command again.

Cluster Reactivation¶

You can now restore the cluster to high availability operation.

Run the following command to remove all nodes from standby mode (it doesn’t matter which node this command is run on):
```
# pcs node unstandby --all
```
Please ensure your cluster is healthy by checking the standard procedure described in the section How to check the NetEye Cluster status.
If you previously disabled stonith above to disable fencing, re-enable it:
```
# pcs property set stonith-enabled=true
```

NetEye Satellites¶

To update a Satellite it is required to have the configuration archive located in /root/satellite-setup/config/<neteye_release>/satellite-config.tar.gz.

To automatically download the latest update you can run the following command on the Satellite:

neteye satellite update

The command will download and install the latest version of both Operating System packages and NetEye stable packages.

Please check for any .rpmnew and .rpmsave files (see the Migrate RPM Configuration section for further information).

If the command is successful, a message will inform you that it is possible to continue the update procedure.

Execute the command below to setup the Satellite with the new updates:

neteye satellite setup